Aerodynamics of a Tandem-Bladed Axial Compressor Rotor under Circumferential Distortion at Different Rotational Speeds

Amit KUMAR; Jerry T. JOHN; A.M. PRADEEP; R.A.D. AKKERMANS; Dragan KOZULOVIC

doi:10.1007/s11630-024-1965-5

Journal of Thermal Science >

2024 , Vol. 33 >Issue 4: 1340 - 1356

DOI: https://doi.org/10.1007/s11630-024-1965-5

Aerothermodynamics

Aerodynamics of a Tandem-Bladed Axial Compressor Rotor under Circumferential Distortion at Different Rotational Speeds

Amit KUMAR ,
Jerry T. JOHN ,
A.M. PRADEEP ,
R.A.D. AKKERMANS ,
Dragan KOZULOVIC

Expand

1. Department of Aerospace Engineering, Indian Institute of Technology Bombay, Mumbai 400076, India
2. Department of Automotive and Aeronautical Engineering, Hamburg University of Applied Sciences, 20099 Hamburg, Germany
3. Institute of Jet Propulsion, Bundeswehr University Munich, 85577 Neubiberg, Germany

Online published: 2024-07-15

Copyright

Science Press, Institute of Engineering Thermophysics, CAS and Springer-Verlag GmbH Germany, part of Springer Nature 2024

Fold

Abstract

For most aircraft engines, inflow distortion is inevitable. Inflow distortion is known to degrade the aerodynamic performance and stable operating limits of a compressor. Tandem rotor configuration is an arrangement that effectively controls the growth of the boundary layer over the suction surface of the blade. Therefore, a higher total pressure rise can be achieved through this unconventional design approach involving the splitting of the blade into forward and aft sections. It is expected that the effect of inlet flow distortion would be more severe for a tandem-rotor design due to the greater flow turning inherent in such designs. However, this aspect needs to be thoroughly examined. The present study discusses the effect of circumferential distortion on the tandem-rotor at different rotational speeds. Full-annulus RANS simulations using ANSYS CFX are used in the present study. The performance of the rotor at a particular flow coefficient and different rotational speeds is compared. The total pressure and efficiency are observed to drop at lower mass flow rates under the influence of circumferential distortion. The loss region in each blade passage is mainly associated with the blade wake, tip leakage vortex, secondary flow, and boundary layer. However, their contribution varies from passage to passage, particularly in the distorted sector. At the lower span, the wake width is found to be higher than that at a higher span. Due to the redistribution of the mass flow, the circumferential extent reduces at a higher span. In the undistorted sector, the strength of the tip leakage vortex is significantly higher at the design rotational speed than at lower speeds. The distortion near the tip region promotes an early vortex breakdown even at the design operating condition. This adversely affects the total pressure, efficiency, and stall margin. Under clean flow conditions, this phenomenon is only observed near the stall point. At the design operating condition, the breakdown of the forward rotor tip leakage vortex is detected in four blade passages. The axial velocity deficit and adverse pressure gradient play a significant role in the behaviour of tip leakage vortex at lower rotational speeds in the distorted sector. A twin vortex breakdown is also observed at lower speeds.

Key words： tandem rotor; circumferential distortion; loss; tip leakage vortex; vortex breakdown; diffusion factor; aerodynamics of compressor blade

Cite this article

Amit KUMAR , Jerry T. JOHN , A.M. PRADEEP , R.A.D. AKKERMANS , Dragan KOZULOVIC . Aerodynamics of a Tandem-Bladed Axial Compressor Rotor under Circumferential Distortion at Different Rotational Speeds[J]. Journal of Thermal Science, 2024 , 33(4) : 1340 -1356 . DOI: 10.1007/s11630-024-1965-5

References

[1] Hynes T.P., Greitzer E.M., A method for assessing effects of circumferential flow distortion on compressor stability. ASME Journal of Turbomachinery, 1987, 109(3): 371–379. https://doi.org/10.1115/1.3262116
[2] Longley J.P., Greitzer E.M., Inlet distortion effects in aircraft propulsion system integration. Steady and Transient Performance Prediction of Gas Turbine Engines, AGARD Lecture Series 183, 1992. https://ntrs.nasa.gov/citations/19920019221
[3] Cao T., Vadlamani N R., Tucker P.G., Smith A.R., Slaby M., Sheaf C.T.J., Fan-intake interaction under high incidence. ASME Journal of Engineering for Gas Turbines and Power, 2017, 139(4): 041204. https://doi.org/10.1115/1.4034701
[4] Zantopp S., MacManus D., Murphy J., Computational and experimental study of intake ground vortices. The Aeronautical Journal, 2010, 114(1162): 769–784. https://doi.org/10.1017/S0001924000004255
[5] Sohoni N.G., Hall C.A., Parry A.B., The influence of an upstream pylon on open rotor aerodynamics at angle of attack. ASME Journal of Turbomachinery, 2019, 141(2): 021006. https://doi.org/10.1115/1.4041082
[6] Perovic D., Hall C.A., Gunn E.J., Stall inception in a boundary layer ingesting fan. ASME Journal of Turbomachinery, 2019, 141(9): 091007. https://doi.org/10.1115/1.4043644
[7] Greitzer E.M., Surge and rotating stall in axial flow compressors—Part I: Theoretical compression system model. ASME Journal of Engineering for Gas Turbines and Power, 1976, 98(2): 190–198.  https://doi.org/10.1115/1.3446138
[8] Murphy J.P., MacManus D.G., Ground vortex aerodynamics under cross-wind conditions. Experiments in Fluids, 2011, 50: 109–124.
https://doi.org/10.1007/s00348-010-0902-4
[9] Zhang W., Stapelfeldt S, Vahdati M., Influence of the inlet distortion on fan stall margin at different rotational speeds. Aerospace Science and Technology, 2020, 98: 105668. https://doi.org/10.1016/j.ast.2019.105668
[10] Choi M., Vahdati M., Imregun M., Effects of fan speed on rotating stall inception and recovery. ASME Journal of Turbomachinery, 2011, 133(4): 041013. https://doi.org/10.1115/1.4003243
[11] Fidalgo V.J., Hall C.A., Colin Y., A study of fan-distortion interaction within the NASA rotor 67 transonic stage. ASME Journal of Turbomachinery, 2012, 134(5): 051011. https://doi.org/10.1115/1.4003850
[12] Gunn E.J., Tooze S.E., Hall C.A., Colin Y., An experimental study of loss sources in a fan operating with continuous inlet stagnation pressure distortion. ASME Journal of Turbomachinery, 2013, 135(5): 051002. https://doi.org/10.1115/1.4007835
[13] Baretter A., Godard B., Joseph P., et al., Experimental and numerical analysis of a compressor stage under flow distortion. International Journal of Turbomachinery, Propulsion and Power, 2021, 6(4): 43.  https://doi: 10.3390/ijtpp6040043
[14] Baretter A., Joseph P., Roussette O., Romanó F., Dazin A., Experimental analysis of an axial compressor operating under flow distortion. Proceedings of the ASME Turbo Expo 2022, ASME Paper No: GT2022-82394. https://doi.org/10.1115/GT2022-82394
[15] Pardo A.C., Hall C.A., Aerodynamics of boundary layer ingesting fuselage fans. ASME Journal of Turbomachinery, 2021, 143(4): 041007. https://doi.org/10.1115/1.4049918
[16] Saha U.K., Roy B., Experimental investigations on tandem compressor cascade performance at low speeds. Experimental Thermal and Fluid Science, 1997, 14(3): 263–276. https://doi.org/10.1016/S0894-1777(96)00125-2
[17] McGlumphy J., Ng W., Wellborn S.R., Kempf S., Numerical investigation of tandem airfoils for subsonic axial-flow compressor blades. ASME Journal of Turbomachinery, 2009, 131(2): 021018. https://doi.org/10.1115/1.2952366
[18] Falla G.A.C., Numerical investigation of the flow in tandem compressor cascades. Master’s thesis, Institute of Thermal Power Plants, Vienna University of Technology, Austria, 2004.
[19] Shen C., Qiang X., Teng J., Numerical and experimental investigation of an axial compressor flow with tandem cascade. Journal of Thermal Science, 2012, 21(6): 500–508. https://doi.org/10.1007/s11630-012-0574-x
[20] Kumar A., Pradeep A.M., Design methodology of a highly loaded tandem rotor and its performance analysis under clean and distorted inflows. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 2021, 235(23): 6798–6821.  https://doi.org/10.1177/09544062211016021
[21] Hasegawa H., Matsuoka A., Suga S., Development of highly loaded fan with tandem cascade. 2003, AIAA Paper No: 2003-1065. https://doi.org/10.2514/6.2003-1065
[22] Kumar A., Pradeep A.M., Performance evaluation of a tandem rotor under design and off-design operation. Proceedings of the ASME Turbo Expo, 2018, ASME Paper No: GT2018-75478. https://doi.org/10.1115/GT2018-75478
[23] Kumar A., Chhugani H., More S., Pradeep A.M., Effect of differential tip clearance on the performance of a tandem rotor. ASME Journal of Turbomachinery, 2022, 144(8): 081007.
[24] Müller L., Kožulović D., Wulff D., Fischer S., Stark U., High turning compressor tandem cascade for high subsonic flows – Part 2: Numerical and experimental investigations. 47th AIAA/ASME/SAE/ASEE Joint Propulsion Conference & Exhibit, 2012, AIAA Paper No: 2011-5602. https://doi.org/10.2514/6.2011-5602
[25] Schneider T., Kožulović D., Flow characteristics of axial compressor tandem cascades at large off-design incidence angles. Proceedings of ASME Turbo Expo, 2013, ASME Paper No. GT2013-94708. https://doi.org/10.1115/GT2013-94708
[26] Bӧhle M., Frey T., Numerical and experimental investigations of the three-dimensional-flow structure of tandem cascades in the sidewall region. ASME Journal of Fluids Engineering, 2014, 136(7): 071102. https://doi.org/10.1115/1.4026880
[27] Mohsen M., Owis F.M., Hashim A.A., The impact of tandem rotor blades on the performance of transonic axial compressors. Aerospace Science and Technology, 2017, 67: 237–248. https://doi.org/10.1016/j.ast.2017.04.019
[28] Song Z., Liu B., Optimization design for tandem cascades of compressors based on adaptive particle swarm optimization. Engineering Applications of Computational Fluid Mechanics, 2018, 12(1): 535–552. https://doi.org/10.1080/19942060.2018.1474806
[29] Eckel J., Gümmer V., Numerical investigation of compressor tandem aerofoils featuring near-endwall modification. Journal of Physics: Conference Series, 2021, 1909: 012019. https://doi:10.1088/1742-6596/1909/1/012019
[30] Kumar A., Pradeep A.M., Response of a tandem-staged compressor to circumferential inflow distortion. ASME Journal of Fluids Engineering, 2022, 144(9): 091202. https://doi.org/10.1115/1.4053955
[31] Liu H., Yue S., Wang Y., Zhang J., Unsteady study on the effects of matching characteristic of tandem cascade on the performance and flow at large angle of attack. Journal of Thermal Science, 2018, 27: 505–515.
[32] Kumar A., Pradeep A.M., Experimental investigation of tandem rotor under clean and radially distorted inflows. Propulsion and Power Research, 2021, 10(3): 247–261.  https://doi.org/10.1016/j.jppr.2021.05.004
[33] Denton J., Loss mechanisms in turbomachines. ASME Journal of Turbomachinery, 1993, 115(4): 621–656. https://doi.org/10.1115/1.2929299
[34] Inoue M., Kuroumaru M., Fukuhara M., Behavior of tip leakage flow behind an axial compressor rotor. ASME Journal of Engineering for Gas Turbines and Power, 1986, 108(1): 7–14.  https://doi.org/10.1115/1.323988981007
[35] Taylor J.V., Miller R.J., Competing three-dimensional mechanisms in compressor flows. ASME Journal of Turbomachinery, 2017, 139(2): 021009. https://doi.org/10.1115/1.4034685

Options

Outlines

模态框（Modal）标题

Journal of Thermal Science

Abstract

Cite this article

References