As a new type of equipment for solar medium temperature utilization, the compound parabolic concentrator-pulsating heat pipe solar collector (CPC-PHPSC) uses pulsating heat pipe (PHP) as an endotherm, which can realize efficient energy conversion. The design of proper concentration ratio of compound parabolic concentrator (CPC) ensures that the incident sunlight can be concentrated on the evaporator section surface of PHP without solar tracking system. The objective of the present work is to study the influence of solar radiation intensity, air speed, material thickness (glass and insulation board) and tilt angle on the thermal performance of the new collector, which is difficult to control in the experiment. The heat leakage process and characteristics of the CPC-PHPSC were numerically studied by establishing a 3D numerical model of the collector unit. The results show that the theoretical collector efficiency of CPC-PHPSC reaches 74.5%, which is consistent with the experimental results. During operation, the heat collection performance is the best when the tilt angle is 45° and the solar radiation intensity is 1000 W/m2, while the excessive air speed will increase the convective heat loss. Increasing the thickness of insulation board and glass has little effect on the collector efficiency.
XU Rongji
,
CHEN Jingyan
,
ZHANG Xiaohui
,
WANG Ruixiang
,
XU Shuhui
. Heat Leakage Numerical Investigation of a Compound Parabolic Concentrator- Pulsating Heat Pipe Solar Collector[J]. Journal of Thermal Science, 2022
, 31(5)
: 1318
-1326
.
DOI: 10.1007/s11630-020-1293-3
[1] Bai Z., Sun J., Liu Q., Comprehensive assessment of line-/point-focus combined scheme for concentrating solar power system. International Journal of Energy Research, 2018, 42(5): 1983‒1998.
[2] Xu R.J., Zhang X.H., et al., Experimental investigation of a solar collector integrated with a pulsating heat pipe and a compound parabolic concentrator. Energy Conversion and Management, 2017, 148: 68‒77.
[3] Pandey K.M., Chaurasiya R., A review on analysis and development of solar flat plate collector. Renewable & Sustainable Energy Reviews, 2017, 67: 641‒650.
[4] Kundu B., Analytic method for thermal performance and optimization of an absorber plate fin having variable thermal conductivity and overall loss coefficient. Applied Energy, 2010, 87(7): 2243‒2255.
[5] Zhu T.T., et al., Performance evaluation of a novel flat-plate solar air collector with micro-heat pipe arrays (MHPA). Applied Thermal Engineering, 2017, 118: 1‒16.
[6] Zhang D., Tao H., Wang M., et al., Numerical simulation investigation on thermal performance of heat pipe flat-plate solar collector. Applied Thermal Engineering, 2017, 118: 113‒126.
[7] Chen M.D., Liu X.B., Numerical simulation on v shaped solar flat-plate air collector. Advanced Materials Research, 2012, 594‒597: 2175‒2178.
[8] Shi Y.H., Zhu L.J., Cao Y.Z., et al., Numerical simulation study on optimization of solar flat-plate collector. Applied Mechanics & Materials, 2014, 635‒637: 523‒527.
[9] Zhang J., Tao H., Chen S., Numerical simulation for structural parameters of flat-plate solar collector. Solar Energy, 2015, 117: 192‒202.
[10] Ahmadi A., Ganji D.D., Jafarkazemi F., Analysis of utilizing Graphene nanoplatelets to enhance thermal performance of flat plate solar collectors. Energy Conversion & Management, 2016, 126(16): 1‒11.
[11] Liu L.K., Jia Y.T., Lin Y.X., et al., Numerical study of a novel miniature compound parabolic concentrating photovoltaic/thermal collector with microencapsulated phase change slurry. Energy Conversion and Management, 2017, 153: 106‒114.
[12] Kudish A.I., Evseev E.G., Walter G., et al., Simulation study of a solar collector with a selectively coated polymeric double walled absorber plate. Energy Conversion & Management, 2002, 43(5): 651‒671.
[13] Kargarsharifabad H., Mamouri S.J., Shafii M.B., et al., Experimental investigation of the effect of using closed- loop pulsating heat pipe on the performance of a flat plate solar collector. Journal of Renewable & Sustainable Energy, 2013, 5(1): 1753‒1766.
[14] Rittidech S., Donmaung A., Kumsombut K., Experimental study of the performance of a circular tube solar collector with closed-loop oscillating heat-pipe with check valve (CLOHP/CV). Renewable Energy, 2009, 34(10): 2234‒2238.
[15] Rittidech S., Wannapakne S., Experimental study of the performance of a solar collector by closed-end oscillating heat pipe (CEOHP). Applied Thermal Engineering, 2007, 27(11–12): 1978‒1985.
[16] Yang Y.P., Xian H.Z., Liu D.Y., et al., Investigation on the feasibility of oscillating-flow heat pipe applied in the solar collector. International Journal of Green Energy, 2009, 6(5): 426‒436.
[17] Kargarsharifabad H., Shafii M.B., Rahni M.T., et al., Exergy analysis of a flat plate solar collector in combination with heat pipe. International Journal of Environmental Research, 2014, 8(1): 39‒48.
[18] Li L., Sun J., Li Y.S., Thermal load and bending analysis of heat collection element of direct-steam-generation parabolic-trough solar power plant. Applied Thermal Engineering, 2017, 127: 1530‒1542.
[19] Li G.Q., Design and development of a lens-walled compound parabolic concentrator-A review. Journal of Thermal Science, 2019, 28(1): 19‒31.
[20] Zhang H.F., Principles and computer simulation of solar thermal utilization. Northwestern Polytechnic University Press, 2004. (in Chinese)
