Printed circuit heat exchangers (PCHEs) are considered as the most promising heat exchangers for use of the supercritical carbon dioxide (S-CO2) Brayton cycle. As crucial components operating at high pressure and thermal load at the same time, PCHE structural integrity evaluations are essential. In this study, to assess the structural strength of PCHEs serving as recuperators and precoolers in the S-CO2 Brayton cycle as a waste heat recovery system for marine engines, the finite element method (FEM) is used and compared with a currently used method from ASME codes. The effects of temperature and pressure on the hot and cold sides are studied in terms of the temperature and pressure differences between the two sides and the main factors affecting its strength discussed. Then, detailed stress intensities of a PCHE under design conditions are investigated, and the results indicate that the highest stress appears at the middle of the semicircular arc of the channel, except for a concentration near the channel tip regions. Stresses of the PCHE are mainly caused by both pressure and temperature differences, with the minimum effect from temperature. The synthesis of the temperature and pressure fields exhibits a complicated action on the total stress under the design conditions. FEM was a more comprehensive means for structural assessment than the method from ASME codes. Further structural optimization of PCHE is conducted to ensure a maximum life span. This research work can provide theoretical guidance for structural integrity assessment of PCHE for the S-CO2 Brayton cycle.
WANG Jian
,
YAN Xinping
,
LU Mingjian
,
SUN Yuwei
,
WANG Jiawei
. Structural Assessment of Printed Circuit Heat Exchangers in Supercritical CO2 Waste Heat Recovery Systems for Ship Applications[J]. Journal of Thermal Science, 2022
, 31(3)
: 689
-700
.
DOI: 10.1007/s11630-022-1493-0
[1] Yoonhan A., Seong J.B., Minseok K., et al., Review of supercritical CO2 power cycle technology and current status of research and development. Nuclear Engineering and Technology, 2015, 47(6): 647–661.
[2] Dostal V., Hejzlar P., Driscoll M.J., High-performance supercritical carbon dioxide cycle for next-generation nuclear reactors. Nuclear Technology, 2006, 154(3): 265–282.
[3] Mecheri M., Le M.Y., Supercritical CO2 Brayton cycles for coal-fired power plants. Energy, 2016, 103: 758–771.
[4] Sharma O.P., Kaushik S.C., Manjunath K., Thermodynamic analysis and optimization of a supercritical CO2 regenerative recompression Brayton cycle coupled with a marine gas turbine for shipboard waste heat recovery. Thermal Science and Engineering Progress, 2017, 3: 62–74.
[5] Yan X., Wang J., Sun Y., et al., Review on S-CO2 Brayton cycle power generation technology based on ship waste heat recovery utilization. China Mechanical Engineering, 2019, 30(8): 939–946.
[6] Sun Y., Yan X., Yuan C., et al., Insight into tribological problems of green ship and corresponding research progresses. Friction, 2018, 6(4): 472–483.
[7] Eric N., Anderson M., Corradini M.L., Numerical investigation of pressure drop and local heat transfer of supercritical CO2 in printed circuit heat exchangers. Supercritical CO2 Power Cycle Symposium, Boulder, Colorado, USA. 2011
[8] Chen M., Sun X., Christensen R.N., Pressure drop and heat transfer characteristics of a high-temperature printed
circuit heat exchanger. Applied Thermal Engineering, 2016, 108: 1409–1417.
[9] Kim D.E., Kim M.H., Cha J.E., Numerical investigation on thermal-hydraulic performance of new printed circuit heat exchanger model. Nuclear Engineering & Design, 2008, 238(12): 3269–3276.
[10] Kim Y.H., Seo J.E., Choi Y.J., et al., Heat transfer and pressure drop characteristics in straight microchannel of printed circuit heat exchangers. Transactions of the Korean Society of Mechanical Engineers B, 2008, 32(12): 915–923.
[11] Chen M., Sun X., Christensen R.N., Dynamic behavior of a high-temperature printed circuit heat exchanger: numerical modeling and experimental investigation. Applied Thermal Engineering, 2018, 135: 246–256.
[12] Lee Y., Lee J.I., Structural assessment of intermediate printed circuit heat exchanger for sodium-cooled fast reactor with supercritical CO2 cycle. Annals of Nuclear Energy, 2014, 73: 84–95.
[13] Jeon S., Baik Y.J., Byon C., Thermal performance of heterogeneous PCHE for supercritical CO2 energy cycle. International Journal of Heat and Mass Transfer, 2016, 102: 867–876.
[14] Hou Y., Tang G., Thermal-hydraulic-structural analysis and design optimization for micron-sized printed circuit heat exchanger. Journal of Thermal Science, 2018, 28(2): 252–261.
[15] Song K.N., Hong S.D., Evaluation of elastic structural integrity of a 70 kW class lab-scale PCHE prototype under the test conditions of HELP. Key Engineering Materials, 2013, 4(4): 577–578.
[16] Johnson I., Choate W.T. Davidson A., Waste heat recovery. Technology and Opportunities in U.S. Industry, 2008.
[17] Yoonhan A., Seong J.B., Minseok K., et al., Review of supercritical CO2 power cycle technology and current status of research and development. Nuclear Engineering and Technology, 2015, 47(6): 647–661.
[18] David S., Le P.R., Stephen J.D., Design considerations for compact heat exchangers. Proceedings of ICAPP’08, Anaheim, USA, 2008.
[19] Le P.R., Southall D., Osborne S., Impact of mechanical design issues on printed circuit heat exchangers. Supercritical CO2 Power Cycle Symposium, Boulder, Colorado, USA. 2011.
[20] ASME boiler and pressure vessel code section VIII, New York, USA, 2015.
