In the process of inlet/engine matching, large-scale distortion vortexes would be generated due to lip separation, curved duct, shock-wave boundary layer interaction and other factors of inlet, resulting in complex combination distortion of total pressure and swirl, which would affect the stable and efficient operation of fans /compressors of aero-engine. On the basis of main distortion vortex characteristics of a typical S-shape inlet and its theoretical model of velocity and pressure distribution, this paper establishes an inlet boundary condition definition method to generate three-dimensional distortion vortex, and presents a study of coupling effect between steady distortion vortex and NASA Rotor 67. The results show that the fan’s performance curve would move to smaller mass flow direction under the influence of the co-rotating distortion vortex, while fan’s operation curve would change to the opposite direction if the inlet distortion vortex direction is opposite to the fan’s rotating direction. Compared with co-rotating distortion vortex, the efficiency loss caused by counter-rotating distortion vortex would be larger and total pressure ratio loss would be smaller. The vortex core size has significant influence on the stability margin of the fan, but has little influence on the efficiency and total pressure ratio characteristic. As the vortex core size increases, the range of fan’s tip region with high attack angle would become larger and cause the fan to stall in advance. Due to the non-uniform suction of the downstream fan, the inlet distortion vortex accelerates to mix with the surrounding main flow. The total pressure distortion decreases and swirl distortion increases along sections from inlet boundary to the fan leading edge.
LIU Zepeng
,
HUANG Guoping
,
CHEN Jie
,
YU Zonghan
. Coupling Effect between Inlet Distortion Vortex and Fan[J]. Journal of Thermal Science, 2023
, 32(3)
: 1089
-1104
.
DOI: 10.1007/s11630-023-1780-4
[1] Cousins W.T., History, philosophy, physics, and future directions of aircraft propulsion system/inlet integration. ASME Paper No: GT2004-54210, 2004.
[2] Zachos P.K., Macmanus D.G., Prieto D.G., et al., Flow distortion measurements in convoluted aero engine intakes. AIAA Journal, 2016, 54(9): 1–14.
[3] Williams D.D., Yost J.O., Some aspects of inlet/engine flow compatibility. The Aeronautical Journal, 1973, 77: 483–492.
[4] Zhang W., Vahdati M., A parametric study of the effects of inlet distortion on fan aerodynamic stability. Journal of Turbomachinery, 2019, 141(1): 011011.
[5] Zhang W., Stapelfeldt S., Vahdati M., Influence of the inlet distortion on fan stall margin at different rotational speeds. Aerospace Science and Technology, 2020, 98: 105668.
[6] Bouldin B., Krishnan P.M., Sheoran Y., Compressor performance and operability in swirl distortion. Journal of Turbomachinery, 2012, 134(4): 041008.
[7] Li J.C., Du J., Liu Y., et al., Effect of inlet radial distortion on aerodynamic stability in a multi-stage axial flow compressor. Aerospace Science and Technology, 2020, 105: 105886.
[8] Li J.C., Du J., Geng S., et al., Tip air injection to extend stall margin of multi-stage axial flow compressor with inlet radial distortion. Aerospace Science and Technology, 2019, 96: 105668.
[9] Voytovych D.M., Xia G., Lian C., et al., Investigation of effects of radial distortion on transonic fan behavior. ASME Paper No: FEDSM-ICNMM2010-30512, 2010.
[10] Zhang H.G., An K., Tan F., et al., Numerical investigation of effect of inlet distortion on compressor flow field and stability. ASME Paper No: GT2017-63369, 2017.
[11] Arend D., Castner R., Frate F., A low cost, compact and versatile rig for integrated inlet and propulsion systems research. 44th AIAA Aerospace Sciences Meeting and Exhibit, AIAA 2006-1313, 2006.
[12] Hale A., Davis M., Sirbaugh J., A numerical simulation capability for analysis of aircraft inlet-engine compatibility. Journal of Engineering for Gas Turbines & Power, 2006, 128(3): 473–481.
[13] Giuliani J.E., Chen J.-P., Fan response to boundary-layer ingesting inlet distortions. AIAA Journal, 2016, 54(10): 3232–3243.
[14] Carnevale M., Wang F., Mare L., Low frequency distortion in civil aero-engine intake. Journal of Engineering for Gas Turbines & Power Transactions of the ASME, 2017, 139(4): 041203.
[15] Mao Y., Dang T.Q., A three-dimensional body-force model for Nacelle-Fan systems under inlet distortions. Aerospace Science and Technology, 2020, 106: 106085.
[16] Song G., Li J., Tang M., et al., Experimental simulation methodology and spatial transition of complex distortion fields in a S-shaped inlet. Aerospace Science and Technology, 2021, 116: 106855.
[17] Gil-Prieto D., Zachos P.K., Macmanus D.G., et al., Unsteady characteristics of S-duct intake flow distortion. Aerospace Science and Technology, 2018, 84: 938–952.
[18] Gil-Prieto D., Macmanus D.G., Zachos P.K., et al., Assessment methods for unsteady flow distortion in aero-engine intakes. Aerospace Science and Technology, 2017, 72: 292–304.
[19] Strazisar A.J., Wood J.R., Hathaway M.D., et al., Laser anemometer measurements in a transonic axial-flow fan rotor. NASA Technical Paper 2879 90N11245.
[20] Vatistas G.H., Kozel V., Mih W.C., A simpler model for concentrated vortices. Experiments in Fluids, 1991, 11(1): 73–76.
[21] Bhagwat M.J., Leishman J.G., Generalized viscous vortex model for application to free-vortex wake and aeroacoustic calculations. Annual Forum Proceedings, 2002.
[22] Mclelland G., Cugno D., Macmanus D.G., et al., Boundary conditions for vortex CFD simulations. ASME Paper No: GT2012-68718, 2012.
[23] Zhang X.F., Jiang J., Fu X.G., Numerical simulation and characteristics analysis of swirl distortion in the S-duct inlet. Gas Turbine Experiment and Research, 2012.
